Water Heater Maintenance

Water Heater Maintenance

Water Heater Maintenance Near Fort Collins, CO

Importance of Water Heater Maintenance

Proper water heater maintenance is crucial for extending its lifespan and improving efficiency. Regular maintenance can prevent costly repairs or replacements in the long run. By ensuring that all components are in good working condition, water heater maintenance can help to avoid breakdowns and the inconvenience of not having hot water.

One of the key benefits of water heater maintenance is the prevention of sediment and limescale buildup. Over time, these deposits can accumulate inside the tank, decreasing efficiency and potentially damaging the components. Regular maintenance, such as flushing the tank to remove sediment buildup, can help to keep the water heater running smoothly and efficiently.

Additionally, regular maintenance can help to identify and address any small issues before they escalate into major problems. This can ultimately save money by avoiding expensive repairs or the need for a new water heater.

Call Today for
Service Right Away

Or Call

About Us

Promotions

We offer promotions on our services, to save you money while providing exceptional service.

Cost Effective Promotions
Promotions

We offer promotions on our services, to save you money while providing exceptional service.

Regular Maintenance Tasks

Regular maintenance tasks are essential for keeping your water heater in good condition in Fort Collins, CO. Here are some tasks that should be performed regularly:

To properly drain the hot water tank and remove sediment build-up, first switch off the cold-water valve. Then, attach a garden hose to the drain valve and place a bucket below to catch the water. Next, open the drain valve and run a hot-water faucet to help flush out the sediments. Stir up the sediment in the tank by briefly opening the cold-water supply valve, drain, and repeat until clean water comes out of the hose.

Once the water runs clear, refill the tank, close the drain valve, and turn its power back on. This process is essential for water heater maintenance and will help to ensure a more efficient and longer-lasting water heater. By following these steps, you can effectively remove sediment build-up and maintain the performance of your hot water tank.

To begin the process of flushing sediment buildup from your water heater, turn off the water heater and allow the water to cool down. Then, connect a garden hose to the drain valve located at the bottom of the water heater. Position the other end of the hose where the sediment and hot water can safely drain without causing any damage.

Next, open the drain valve and let the water and sediment flow out until the water runs clear. This may take a few minutes, and it’s important to remove all sediment to ensure the water heater functions properly.

After all the sediment has been flushed out and the water runs clear, close the drain valve and disconnect the hose. Finally, turn the water heater back on and allow it to heat the new water.

How to check and replace anode rods in hot water tanks:

1. Start by turning off the water heater and allowing the water in the tank to cool.

2. Once the water has cooled, connect a garden hose to the drain valve at the bottom of the tank and drain about 10% of the water from the tank to reduce the pressure.

3. Locate the anode rod, which is usually located on the top of the water heater. It is a long, metal rod that extends into the tank.

4. Using a wrench, loosen the hex head of the anode rod to inspect it for corrosion. If the rod is heavily corroded, it is time to replace it.

5. If the anode rod is in good condition, you can reinstall it by tightening the hex head back in place.

6. If the anode rod needs to be replaced, you can purchase a new one from a hardware store. Make sure to get the right size and type for your specific water heater.

7. Once you have the new anode rod, insert it into the water heater and tighten the hex head back in place.

Regularly checking and replacing the anode rod in your water heater is essential for preventing corrosion and maintaining the efficiency and longevity of the heater. It is recommended to perform this maintenance at least once a year for optimal performance and to prolong the life of your hot water tank.

Inspecting the pressure relief valve on your water heater is an important maintenance task to ensure that it is functioning properly. To start, position a bucket underneath the valve to catch any water released during the inspection. Then, lift the valve to release some water into the bucket. Once you have released some water, stop lifting the valve to see if the pressure-relief valve switches back down and the water flow stops. If the valve does not switch back down and the water flow does not stop, continue draining the valve until it does. This will help to ensure that the valve is relieving pressure as intended and is not stuck open. By including these simple steps in your regular water heater maintenance routine, you can help prevent potential issues and ensure that your pressure relief valve is in good working condition.

To test the temperature and pressure settings on your water heater, start by locating the T&P (temperature and pressure) valve, which is typically located on the side or top of the water heater. Place a 5-gallon bucket underneath the discharge pipe connected to the T&P valve to catch the water. Ensure the bucket is positioned securely to avoid any spills.

Carefully open the T&P valve by lifting the lever or turning the knob. Let the water flow into the bucket for a few seconds to test the temperature and pressure. Once you’ve collected enough water, carefully close the T&P valve to stop the flow.

After testing, if you find that the T&P valve cannot be opened or if water continues to drip after closing it, it may be a sign that the valve needs to be replaced. In this case, it is best to contact a licensed plumber at JT Plumbing Heating & Air to replace the valve to ensure the safety and functionality of your water heater.

Maintenance Tips for Electric Water Heaters

Electric water heaters are a convenient and energy-efficient way to provide hot water in your home. However, like any appliance, they require regular maintenance to ensure they continue to function properly. By following these maintenance tips for electric water heaters, you can extend the lifespan of your unit, improve its efficiency, and prevent costly repairs. From checking the pressure relief valve to flushing the tank and monitoring the anode rod, these simple maintenance tasks can make a big difference in the performance and longevity of your electric water heater. With a little bit of regular attention, you can enjoy reliable hot water and lower energy bills for years to come.
JT Plumbing Heating and Air
Water Heater Maintenance

Turning Off the Power Supply

To turn off the power supply to an electric water heater, start by locating the circuit breaker for the water heater in your electrical panel. Switch off the circuit breaker labeled for the water heater. This will cut off the power supply to the heating elements and thermostat. For further guidance, refer to the owner’s manual for the specific model of your water heater. It’s essential to follow the manufacturer’s guidelines and consult with a professional if you’re unsure about the process.
Water Heater Maintenance Fort Collins CO

Inspecting Heating Elements

To inspect the heating elements in your water heater, start by unplugging the unit and turning off the power supply to the heater. Then, locate the access panels on the water heater and carefully remove them. Once the panels are removed, visually examine the heating elements for any signs of corrosion or damage. Look for cracks, rust, or any other obvious signs of wear and tear.

If you notice any corrosion or damage, it may be necessary to replace the heating element to ensure the continued efficient operation of the water heater. Additionally, it is important to clean any buildup or debris from the heating elements to prevent interference with their function. Use a soft brush or cloth to gently remove any dirt or debris.

Checking Electrical Connections

When checking the electrical connections within the water heater unit, it is important to ensure that all wires are properly connected and there are no loose or frayed connections that could cause electrical issues. Start by inspecting the connections to the heating element, thermostat, and power supply to make sure they are secure and in good condition. Look for any signs of corrosion or damage to the electrical components, such as rust, oxidation, or melted insulation. Pay close attention to the terminals where the wires are connected, as these areas are prone to corrosion and should be thoroughly examined.

It is also important to check the wiring for any signs of wear or damage that could compromise the electrical connections. Any loose or damaged connections should be tightened or replaced to ensure that the water heater unit operates safely and efficiently. Regularly checking and maintaining the electrical connections in the water heater unit can help prevent potential hazards and extend the life of the appliance.

Maintenance Tips for Gas Water Heaters

Gas water heaters are a popular choice for many households due to their efficiency and cost-effectiveness. However, in order to ensure that your gas water heater continues to function at its best, regular maintenance is essential. In this section, we will cover some important tips to help you keep your gas water heater in top working condition, improve its longevity, and minimize the risk of potential issues. From checking for leaks to flushing the tank, these maintenance tips will help you keep your gas water heater running smoothly and efficiently.

Shutting Off the Gas Supply

To shut off the gas supply to the water heater, start by locating the gas valve connected to the water heater. This valve is usually located near the bottom of the water heater. Before proceeding, make sure to wear safety gloves, goggles, and closed-toe shoes to protect yourself from any potential gas leaks or accidents.

Once you are safely prepared, carefully locate the shut-off valve and turn it to the “off” position. It’s important to handle the gas valve with caution and turn it slowly to prevent any accidents.

This process will stop the flow of gas to the water heater and ensure that it is safe to perform any maintenance, repair, or replacement. It’s essential to always follow safety precautions when working with gas-related appliances to avoid any potential hazards.

Cleaning the Burner and Flue

To clean the burner and flue of the water heater, start by turning off the gas supply and allowing the burner to cool down. Once it is safe to do so, use a brush and vacuum to remove any debris and dust from the burner and flue. Make sure to carefully clean both components to ensure they are free of any obstructions. After using the brush and vacuum, use a damp cloth to wipe down the surfaces and ensure they are clean. Be thorough in this step to remove any remaining dirt or particles. Once everything is clean, turn on the gas supply and check for any obstructions or unusual noises coming from the water heater. Regularly cleaning the burner and flue will help maintain the efficiency and safety of the water heater.
Water Heaters
Water Heaters

Checking for Leaks and Drips

To check for leaks and drips on your water heater, start by shutting off the unit and allowing it to cool down. Once the water heater is safe to touch, inspect the T&P relief valve for any signs of leaking or dripping. If you notice any leaks, it may indicate a problem with the valve and it should be addressed immediately.

Next, check the sacrificial anode rod for deterioration. This rod is designed to attract corrosive elements in the water to protect the tank from rust and corrosion. If the rod shows signs of heavy deterioration or is mostly eaten away, it will need to be replaced to ensure the longevity of your water heater.

When addressing T&P relief valve drips, first, try lifting and lowering the valve’s lever a few times to see if it can dislodge any debris that may be causing the leak. If the issue persists, it’s recommended to contact a professional plumber to properly diagnose and fix the problem.

Regularly inspecting and addressing leaks and drips on your water heater, as well as maintaining the T&P relief valve and sacrificial anode rod, can help ensure the efficient and safe operation of your unit.

Five-Star Water Heater Maintenance Service

Ensure the durability and efficiency of your water heater by turning to JT Plumbing Heating & Air in Fort Collins, CO. Our team of experienced technicians specializes in providing top-notch maintenance services for your water heater. We understand the importance of a smoothly functioning water heater in your daily life, and our proactive maintenance approach aims to identify and address potential issues before they become disruptive.

Trust us to go the extra mile for customer satisfaction, optimizing your water heater’s performance and contributing to energy efficiency, ultimately saving you money on utility bills. Choose JT Plumbing Heating & Air for reliable and prompt maintenance services tailored to the unique climate and conditions of Fort Collins. Experience the difference with our commitment to quality, reliability, and customer happiness – schedule your water heater maintenance today for a consistently dependable hot water supply.

Best Water Heater Maintenance & Tune-Up Deals from JT Plumbing, Heating & Air

$79 Water Heater Repair

Consulation + 2 Hour Arriva
99
$79
00
  • We will come to your home
  • Diagnose the problem with your water heater system
  • Provide a comprehensive report on the problem
  • Present you with personalized solutions on what to do next
  • If we do the work we will waive the diagnostic charge!
  • Up to 4-Year Warranties available on parts and labor.
  • 100% satisfaction guaranteed
  • NO service call fees. NO dispatch fees.

$79 Water Heater Tune-Up

Consulation+ 2 Hour Arrival
99
$79
00
  • We'll provide our precision tune-up with a no-breakdown guarantee. If your system breaks down within 6 months of service:
  • We’ll give you priority scheduling service
  • We’ll come out at no cost to diagnose the problem
  • Present you with personalized solutions on what to do next
  • Credit your original tune-up charge toward the repair!
  • Up to 4-Year Warranties available on parts and labor
  • 100% Satisfaction Guaranteed
  • NO service call fees. NO dispatch fees.

Water Heater Install for as Low as $99/mo + Next Available Plumber

$99
00
  • We will come to your home
  • Analyze your new water heater installation needs
  • Present you with personalized solutions on what to do next
  • Financing options available!
  • Up to 12-Year Warranties available on parts and labor
  • 100% satisfaction guaranteed
  • NO service call fees. NO dispatch fees
  •  
  •  

FAQ About Water Heater Maintenance

What Maintenance Is Needed Or A Water Heater?

There are a number of tasks a JT Plumbing, Heating & Air technician might complete when servicing your home’s water heater. JT Plumbing, Heating & Air technicians are the premier source in the Fort Collins, CO for water heater maintenance. Call (970) 818-1613 to schedule an appointment!

How Often Should Maintenance Be Done On A Water Heater?

Maintenance should be performed at least once annually, if not twice annually. Your water heater tank should be flushed once per year. Call JT Plumbing, Heating & Air to schedule your water heater’s professional maintenance.

What Happens If You Don’t Flush Your Water Heater?

Failure to have your water heater flushed will result in scaling and your water heater will corrode. If you don’t flush your water heater, it will shorten the lifespan of your water heater and will also result in declining functionality for your unit.

What Maintenance Is Needed Or A Water Heater?

There are a number of tasks a JT Plumbing & Restoration technician might complete when servicing your home’s water heater. JT Plumbing & Restoration technicians are the premier source in the Fort Collins, CO for water heater maintenance. Call (970) 457-4189 to schedule an appointment!

How Often Should Maintenance Be Done On A Water Heater?

Maintenance should be performed at least once annually, if not twice annually. Your water heater tank should be flushed once per year. Call JT Plumbing & Restoration to schedule your water heater’s professional maintenance.

What Happens If You Don’t Flush Your Water Heater?

Failure to have your water heater flushed will result in scaling and your water heater will corrode. If you don’t flush your water heater, it will shorten the lifespan of your water heater and will also result in declining functionality for your unit.

Schedule Your Water Heater Maintenance Service Now!

With our highly-skilled plumbers and upfront pricing, you can trust JT Plumbing, Heating & Air experts at JT Plumbing Heating & Air for 100% satisfaction guaranteed.

Service Area

Our Service Areas